79 lines
2.8 KiB
Plaintext
79 lines
2.8 KiB
Plaintext
I2C interface to the firmware
|
|
-----------------------------
|
|
|
|
To control the operation of the keyboard's firmware, the firmware
|
|
exposes some "registers" that the user can read/write using the
|
|
two kinds of I2C transfers.
|
|
|
|
1) set values of consecutive block of registers starting from REG_ADDR:
|
|
|
|
START TX(DEV_ADDR+WR REG_ADDR [REG_DATA REG+1_DATA REG+2_DATA ...]) STOP
|
|
|
|
2) read values of consecutive block of registers starting from REG_ADDR:
|
|
|
|
START TX(DEV_ADDR+WR REG_ADDR) STOP
|
|
START TX(DEV_ADDR+RD) RX(REG_ADDR [REG_DATA REG+1_DATA REG+2_DATA ...]) STOP
|
|
|
|
Device address is 0x15.
|
|
|
|
|
|
Registers
|
|
---------
|
|
|
|
0x00: Device ID1 (0x4b)
|
|
0x01: Device ID2 (0x42)
|
|
0x02: Firmware revision
|
|
0x03: System configuration
|
|
bit 0: disable KB scanning (1: scanning disabled, 0: scanning enabled)
|
|
bit 1: poll mode
|
|
1: don't rely on row change detection, poll the matrix periodically
|
|
(prevents MCU power down)
|
|
0: power down the MCU when no key is pressed, and rely on change
|
|
detection on row inupts to wake the MCU up
|
|
bit 2: enable USB debug interface
|
|
1: enabled
|
|
0: disabled
|
|
|
|
0x10: Keyboard data for column 1
|
|
...
|
|
0x0b: Keyboard data for column 12
|
|
0x0c: CRC8 of keyboard data from 0x10-0x0b
|
|
|
|
|
|
0x70: Flashing mode unlock key
|
|
(writing 0x46 to this register unlocks the flashing mode.)
|
|
|
|
0x71: Flashing control
|
|
Writing various commands to this register makes the MCU execute them,
|
|
if the MCU is not executing the previous command. Available commands:
|
|
|
|
0x52 - read a block of data from code ROM
|
|
0x57 - write a block of data to code ROM
|
|
0x45 - erase the code rom memory block (128B)
|
|
0x43 - confirm the validity of the firmware and enable redirection
|
|
to it from the main app (this redirection is automatically
|
|
disabled before executing the 0x57 command)
|
|
|
|
This register will ignore further commands as long as the last operation
|
|
is still in progress. This register will contain the code of the
|
|
currently executed operation, and will be cleared after the operation
|
|
finishes. Completion is also signalled by pulsing the INT pin shortly.
|
|
|
|
If the operation fails, this register will contain value 0xff. If it
|
|
succeeds it will contain value 0x00.
|
|
|
|
0x7d: target address low byte
|
|
0x7e: target address high byte
|
|
|
|
0x7f: CRC8 calculated for the 128B block of data from 0x80-0xff
|
|
- this must be written by the user when preparing data for write
|
|
operation, MCU checks the CRC8 of the data and compares it against
|
|
the value in this register before starting the execution of
|
|
0x57 command
|
|
|
|
- this is updated by the MCU after reading the data from flash memory
|
|
|
|
0x80: 128B block of EEPROM data (either read from code memory or to be
|
|
... written)
|
|
0xff
|